Shop
Showing 49–64 of 168 results
-
-
-
-
-
-
-
-
-
GN-10i Nitrogen Gas Generator
Add to cart- Purpose: Generates nitrogen gas (N₂) with a purity of 99% (N₂ + Ar) for various industrial applications.
- N₂ Production Rate: 10 liters per minute.
- Discharge Pressure: 0.2 MPa.
- Dew Point: Below -60°C.
- Dimensions: 400 mm (W) × 460 mm (D) × 900 mm (H).
- Weight: Approximately 60 kg.
- Power Supply: 100 VAC, single-phase; power consumption of approximately 0.4 kW at both 50Hz and 60Hz.
- Cooling Method: Air-cooled; no external cooling water required.
- Typical Applications: General industrial uses requiring nitrogen gas.
-
Hast (Highly Accelerated Stress Test)
Add to cartThe Standard design is safer,
and the inner arc design
prevents condensation and
dripping, which complies with
national safety container
regulations
• Multiple protection functions, two
high-temperature protection
devices, humidity water cutoff
protection, and overpressure
protection
• Higher stability: equipped with
self-developed PIO control
algorithm.ensuring the accuracy
of temperature,humidity and
pressure values
• Humidity free selection:
saturation and unsaturation free
setting
• High intelligence: USB data,
curve export and save function -
High Vacuum Valve
$100.00Add to cartHigh Vacuum isolation valve for semiconductor, thin film, solar energy, surface treatment, communication, electronics, metallurgy, aviation, aerospace, light industry, chemical industry, food, medicine and other industries. Angle and straight type available. Sizes : KF16, KF25, KF40, KF50 Material: Stainless steel 304+ fluorine rubber + bellows shaft seal
-
HMDS Pre-treatment System
$50,000.00Add to cartThe HMDS pre-treatment system allows controlled adjustment of parameters such as processing temperature, time, and dwell time, enabling uniform HMDS coating on wafer surfaces. This reduces the contact angle post-HMDS treatment, decreases the required amount of photoresist, and improves adhesion between the photoresist and wafer. Better Pre-treatment Performance The system performs HMDS treatment after multiple …
-
HPB-4B
Add to cart- Individual temperature control for each device up to 600 W
- Test devices at a maximum temperature of 150°C with a liquid-cooled heat-sink per device
- Programmable clocks edges with 2-nanosecond edge resolution and 8 on-the-fly timing sets
- System capacity of 14 burn-in boards (112 devices)
- 12 vector formats per-pin per-cycle with memory testing extensions
- 19 programmable voltage regulators provide 2060 amps of device current per burn-in board
- High-speed clock programmable up to 800 MHz
- 128 I/O signals per board
- 64M vector memory, 8G scan
-
HPB-5C+
Add to cart- Individual temperature control for each device up to 150 W
- Variable oven overflow control
- Individual pattern zone per burn-in board slot
- 32M vector memory standard, 64M optional
- Tests devices at a temperature of up to 150°C
- Up to 800 MHz clock rate
- 128 digital I/O channels per burn-in board
- System capacity of 384 devices under test with individual temperature control per device
- 16 programmable voltage regulators with 1080 amps of device under test power per burn-in board
- 8 high-current supplies
- (0-4 volts at up to 125 amps each)
- 8 low-current supplies
- (0-6 volts at up to 10 amps each)
-
HPB-6
Add to cart- Handle devices up to 1000 watts
- 16 independent burn-in board slots
- 64M standard and 128M optional parallel vector depth –subroutine capable
- 8G scan vector depth
- 128 formatted vector I/O channels plus 128 vector output-only channels
- 8 programmable high-frequency clocks, up to 350 MHz – LVDS to the BiB
-
I-V Testing System
Add to cart- Standalone or integrated with the OAI I-V Measurement System
- I-V Test Systems: Standalone or fully Integrated with any OAI Solar Simulator
- Extremely accurate measurements of solar cell I-V
- Parameters & efficiency
- Propritary IV Rider Software measuring critical I-V Parameters
- Standard ranges of I-V testers are: S1a, 1-5A, and 20A – verified at Fraunhofer, ISE, & NREL.
- Multiplexing function to test various solar cells
- Measures up to +/- 35A/ +/-10V/350w I-V RANGE
- Features corrected I-V curves & Graphical/ Tabular QC monitoring
- Optional Normalization Kit to correct any lamp instability
